U-Boot SPL 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800)
WS > Skip chip ID checlDRAM: 1024 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.7(debug):8ef86301-dirty
NOTICE: BL31: Built : 17:07:29, Aug 25 2022
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a082570, model: OrangePi Zero2
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: BL31: WS-master prevent pmix setup
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied
INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
INFO: Changed devicetree.
U-Boot 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero2
I2C: ready
DRAM: 1 GiB
MMC: mmc@4020000: 0
Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Net: phy interface7
Could not get PHY for ethernet@5020000: addr 1
No ethernet found.
Autoboot in 1 seconds, press <Space> to stop
=>
=> setenv bootargs rw init=/sbin/init root=/dev/mmcblk0p1 rootwait console=ttyS0,115200 debug panic=30
=> ext4load mmc 0 0x42000000 /boot/dtb/allwinner/sun50i-h616-orangepi-zero2.dtb
22920 bytes read in 5 ms (4.4 MiB/s)
=> ext4load mmc 0 0x43000000 /boot/uInitrd
11610972 bytes read in 481 ms (23 MiB/s)
=> ext4load mmc 0 0x49000000 /boot/Image
21934088 bytes read in 908 ms (23 MiB/s)
=> env set fdt_high ffffffff
=> booti 0x49000000 0x43000000 0x42000000
## Loading init Ramdisk from Legacy Image at 43000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 11610908 Bytes = 11.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 42000000
Booting using the fdt blob at 0x42000000
Loading Ramdisk to 484ed000, end 48fffb1c ... OK
Loading Device Tree to 00000000484e4000, end 00000000484ec987 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.60-sunxi64 (root@vmcompiler) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk SMP Thu Aug 25 17:47:19 +08 2022
[ 0.000000] Machine model: OrangePi Zero2
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x7fdde100-0x7fddffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000004007ffff]
[ 0.000000] node 0: [mem 0x0000000040080000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] cma: Reserved 128 MiB at 0x0000000076c00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 19 pages/cpu s37144 r8192 d32488 u77824
[ 0.000000] pcpu-alloc: s37144 r8192 d32488 u77824 alloc=19*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: rw init=/sbin/init root=/dev/mmcblk0p1 rootwait console=ttyS0,115200 debug panic=30
[ 0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[ 0.000000] printk: log_buf_len min size: 16384 bytes
[ 0.000000] printk: log_buf_len: 32768 bytes
[ 0.000000] printk: early log buf free: 14392(87%)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 863308K/1048576K available (13568K kernel code, 1068K rwdata, 4164K rodata, 2496K init, 321K bss, 54196K reserved, 131072K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000383] Console: colour dummy device 80x25
[ 0.000478] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000493] pid_max: default: 32768 minimum: 301
[ 0.000566] LSM: Security Framework initializing
[ 0.000595] Yama: becoming mindful.
[ 0.000683] AppArmor: AppArmor initialized
[ 0.000784] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000799] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002529] rcu: Hierarchical SRCU implementation.
[ 0.003712] smp: Bringing up secondary CPUs ...
[ 0.004300] Detected VIPT I-cache on CPU1
[ 0.004381] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004990] Detected VIPT I-cache on CPU2
[ 0.005058] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005639] Detected VIPT I-cache on CPU3
[ 0.005705] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005803] smp: Brought up 1 node, 4 CPUs
[ 0.005833] SMP: Total of 4 processors activated.
[ 0.005840] CPU features: detected: 32-bit EL0 Support
[ 0.005847] CPU features: detected: CRC32 instructions
[ 0.017874] CPU: All CPU(s) started at EL2
[ 0.017923] alternatives: patching kernel code
[ 0.019317] devtmpfs: initialized
[ 0.023403] Registered cp15_barrier emulation handler
[ 0.023433] Registered setend emulation handler
[ 0.023611] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.023634] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.027993] pinctrl core: initialized pinctrl subsystem
[ 0.029373] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.030862] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.031024] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.031146] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.031256] audit: initializing netlink subsys (disabled)
[ 0.031532] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1
[ 0.032082] thermal_sys: Registered thermal governor 'fair_share'
[ 0.032089] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.032096] thermal_sys: Registered thermal governor 'step_wise'
[ 0.032102] thermal_sys: Registered thermal governor 'user_space'
[ 0.032579] cpuidle: using governor menu
[ 0.032738] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.032841] ASID allocator initialised with 65536 entries
[ 0.033048] Serial: AMBA PL011 UART driver
[ 0.046185] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.046212] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.046220] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.046228] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.048047] cryptd: max_cpu_qlen set to 1000
[ 0.116243] raid6: neonx8 gen() 1802 MB/s
[ 0.184310] raid6: neonx8 xor() 1346 MB/s
[ 0.252373] raid6: neonx4 gen() 1844 MB/s
[ 0.320443] raid6: neonx4 xor() 1335 MB/s
[ 0.388505] raid6: neonx2 gen() 1750 MB/s
[ 0.456576] raid6: neonx2 xor() 1227 MB/s
[ 0.524643] raid6: neonx1 gen() 1522 MB/s
[ 0.592709] raid6: neonx1 xor() 1048 MB/s
[ 0.660777] raid6: int64x8 gen() 1252 MB/s
[ 0.728847] raid6: int64x8 xor() 659 MB/s
[ 0.796910] raid6: int64x4 gen() 1394 MB/s
[ 0.864971] raid6: int64x4 xor() 713 MB/s
[ 0.933033] raid6: int64x2 gen() 1189 MB/s
[ 1.001112] raid6: int64x2 xor() 625 MB/s
[ 1.069179] raid6: int64x1 gen() 886 MB/s
[ 1.137252] raid6: int64x1 xor() 460 MB/s
[ 1.137259] raid6: using algorithm neonx4 gen() 1844 MB/s
[ 1.137266] raid6: .... xor() 1335 MB/s, rmw enabled
[ 1.137272] raid6: using neon recovery algorithm
[ 1.138139] reg-fixed-voltage vccgpu: Fixed regulator specified with variable voltages
[ 1.138159] reg-fixed-voltage: probe of vccgpu failed with error -22
[ 1.138556] iommu: Default domain type: Translated
[ 1.138577] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.138889] SCSI subsystem initialized
[ 1.139083] usbcore: registered new interface driver usbfs
[ 1.139126] usbcore: registered new interface driver hub
[ 1.139161] usbcore: registered new device driver usb
[ 1.139441] pps_core: LinuxPPS API ver. 1 registered
[ 1.139449] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.139466] PTP clock support registered
[ 1.139882] ARM FF-A: FFA_VERSION returned not supported
[ 1.140238] Advanced Linux Sound Architecture Driver Initialized.
[ 1.140894] NetLabel: Initializing
[ 1.140903] NetLabel: domain hash size = 128
[ 1.140908] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.140981] NetLabel: unlabeled traffic allowed by default
[ 1.141461] clocksource: Switched to clocksource arch_sys_counter
[ 1.141662] VFS: Disk quotas dquot_6.6.0
[ 1.141716] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.142394] AppArmor: AppArmor Filesystem Enabled
[ 1.148206] NET: Registered PF_INET protocol family
[ 1.148390] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.149202] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.149236] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.149253] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.149328] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 1.149489] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.149640] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.149681] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.149910] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.150425] Trying to unpack rootfs image as initramfs...
[ 1.158344] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 1.164578] Initialise system trusted keyrings
[ 1.164665] Key type blacklist registered
[ 1.164974] workingset: timestamp_bits=44 max_order=18 bucket_order=0
[ 1.170550] zbud: loaded
[ 1.172062] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.174485] integrity: Platform Keyring initialized
[ 1.216948] xor: automatically using best checksumming function 32regs
[ 1.216985] async_tx: api initialized (async)
[ 1.216998] Key type asymmetric registered
[ 1.217007] Asymmetric key parser 'x509' registered
[ 1.217124] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.217335] io scheduler mq-deadline registered
[ 1.217347] io scheduler kyber registered
[ 1.217609] io scheduler bfq registered
[ 1.226545] sun50i-h616-pinctrl 300b000.pinctrl: initialized sunXi PIO driver
[ 1.227472] sun50i-h616-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver
[ 1.230165] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 1.231954] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-ph not found, using dummy regulator
[ 1.232570] printk: console [ttyS0] disabled
[ 1.232667] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 32, base_baud = 1500000) is a 16550A
[ 1.724139] Freeing initrd memory: 11336K
[ 1.728139] printk: console [ttyS0] enabled
[ 2.213123] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 2.223640] loop: module loaded
[ 2.227587] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pc not found, using dummy regulator
[ 2.236577] sun6i-spi 5010000.spi: Failed to request TX DMA channel
[ 2.242864] sun6i-spi 5010000.spi: Failed to request RX DMA channel
[ 2.249741] spi-nor spi0.0: supply vdd not found, using dummy regulator
[ 2.269670] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 2.276586] spi-nor: probe of spi0.0 failed with error -2
[ 2.283352] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.289971] ehci-platform: EHCI generic platform driver
[ 2.295307] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.301504] ohci-platform: OHCI generic platform driver
[ 2.306997] usbcore: registered new interface driver usb-storage
[ 2.313572] mousedev: PS/2 mouse device common for all mice
[ 2.320117] sun6i-rtc 7000000.rtc: registered as rtc0
[ 2.325234] sun6i-rtc 7000000.rtc: setting system clock to 1970-01-02T00:00:21 UTC (86421)
[ 2.333609] sun6i-rtc 7000000.rtc: RTC enabled
[ 2.338163] i2c_dev: i2c /dev entries driver
[ 2.343048] sunxi-wdt 30090a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 2.352259] sdhci: Secure Digital Host Controller Interface driver
[ 2.358507] sdhci: Copyright(c) Pierre Ossman
[ 2.362898] Synopsys Designware Multimedia Card Interface Driver
[ 2.369273] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.369373] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pf not found, using dummy regulator
[ 2.384374] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.384568] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pi not found, using dummy regulator
[ 2.390782] SMCCC: SOC_ID: ID = jep106:091e:1823 Revision = 0x00000000
[ 2.399237] sunxi-mmc 4020000.mmc: Got CD GPIO
[ 2.405922] hid: raw HID events driver (C) Jiri Kosina
[ 2.415319] usbcore: registered new interface driver usbhid
[ 2.420900] usbhid: USB HID core driver
[ 2.434342] NET: Registered PF_INET6 protocol family
[ 2.435652] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 2.470384] Segment Routing with IPv6
[ 2.474162] In-situ OAM (IOAM) with IPv6
[ 2.478183] NET: Registered PF_PACKET protocol family
[ 2.483424] 8021q: 802.1Q VLAN Support v1.8
[ 2.487788] 9pnet: Installing 9P2000 support
[ 2.492175] Key type dns_resolver registered
[ 2.496881] registered taskstats version 1
[ 2.501033] Loading compiled-in X.509 certificates
[ 2.509424] Loaded X.509 cert 'Build time autogenerated kernel key: db547b410d67e79c33dc7f5c06b4cd1f4cb3e184'
[ 2.522199] zswap: loaded using pool zstd/z3fold
[ 2.527669] Key type ._fscrypt registered
[ 2.531733] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.531738] Key type .fscrypt registered
[ 2.531743] Key type fscrypt-provisioning registered
[ 2.548760] mmc0: new high speed SDHC card at address aaaa
[ 2.549745] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=no
[ 2.555069] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 2.571689] mmcblk0: p1
[ 2.575296] Key type encrypted registered
[ 2.579376] AppArmor: AppArmor sha1 policy hashing enabled
[ 2.584914] ima: No TPM chip found, activating TPM-bypass!
[ 2.590439] ima: Allocated hash algorithm: sha1
[ 2.595014] ima: No architecture policies found
[ 2.599591] evm: Initialising EVM extended attributes:
[ 2.604729] evm: security.selinux
[ 2.608048] evm: security.SMACK64
[ 2.611364] evm: security.SMACK64EXEC
[ 2.615028] evm: security.SMACK64TRANSMUTE
[ 2.619124] evm: security.SMACK64MMAP
[ 2.622787] evm: security.apparmor
[ 2.626190] evm: security.ima
[ 2.629153] evm: security.capability
[ 2.632728] evm: HMAC attrs: 0x1
[ 2.644823] usb1-vbus: supplied by vcc-5v
[ 2.649115] sun50i-h616-r-pinctrl 7022000.pinctrl: supply vcc-pl not found, using dummy regulator
[ 2.658334] sunxi-rsb 7083000.rsb: RSB running at 3000000 Hz
[ 2.664171] sunxi-rsb 7083000.rsb: /soc/rsb@7083000/pmic@745: set runtime address failed: -22
[ 2.672863] axp20x-rsb sunxi-rsb-745: AXP20x variant AXP806 found
[ 2.679255] axp20x-regulator axp20x-regulator.1: Error setting dcdc frequency: -5
[ 2.687098] dcdca: supplied by vcc-5v
[ 2.691049] dcdcb: supplied by vcc-5v
[ 2.695032] dcdcc: supplied by vcc-5v
[ 2.699014] dcdcd: supplied by vcc-5v
[ 2.702984] dcdce: supplied by vcc-5v
[ 2.706936] aldo1: supplied by vcc-5v
[ 2.710910] aldo2: supplied by vcc-5v
[ 2.714860] aldo3: supplied by vcc-5v
[ 2.718815] bldo1: supplied by vcc-5v
[ 2.722805] bldo2: supplied by vcc-5v
[ 2.726760] bldo3: supplied by vcc-5v
[ 2.730721] bldo4: supplied by vcc-5v
[ 2.734699] cldo1: supplied by vcc-5v
[ 2.738657] cldo2: supplied by vcc-5v
[ 2.742644] cldo3: supplied by vcc-5v
[ 2.746579] sw: supplied by regulator-dummy
[ 2.750879] axp20x-rsb sunxi-rsb-745: AXP20X driver loaded
[ 2.758134] ehci-platform 5200000.usb: EHCI Host Controller
[ 2.763800] ehci-platform 5200000.usb: new USB bus registered, assigned bus number 1
[ 2.771661] ehci-platform 5200000.usb: irq 36, io mem 0x05200000
[ 2.793477] ehci-platform 5200000.usb: USB 2.0 started, EHCI 1.00
[ 2.799889] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[ 2.808170] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.815404] usb usb1: Product: EHCI Host Controller
[ 2.820287] usb usb1: Manufacturer: Linux 5.15.60-sunxi64 ehci_hcd
[ 2.826470] usb usb1: SerialNumber: 5200000.usb
[ 2.831582] hub 1-0:1.0: USB hub found
[ 2.835420] hub 1-0:1.0: 1 port detected
[ 2.840269] ohci-platform 5200400.usb: Generic Platform OHCI controller
[ 2.846950] ohci-platform 5200400.usb: new USB bus registered, assigned bus number 2
[ 2.854834] ohci-platform 5200400.usb: irq 37, io mem 0x05200400
[ 2.921683] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.15
[ 2.929961] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.937184] usb usb2: Product: Generic Platform OHCI controller
[ 2.943106] usb usb2: Manufacturer: Linux 5.15.60-sunxi64 ohci_hcd
[ 2.949287] usb usb2: SerialNumber: 5200400.usb
[ 2.954355] hub 2-0:1.0: USB hub found
[ 2.958185] hub 2-0:1.0: 1 port detected
[ 2.963118] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator
[ 2.972035] usb_phy_generic usb_phy_generic.1.auto: dummy supplies not allowed for exclusive requests
[ 2.984116] of_cfs_init
[ 2.986756] of_cfs_init: OK
[ 2.989844] ALSA device list:
[ 2.992812] No soundcards found.
[ 2.997498] Freeing unused kernel memory: 2496K
[ 3.002150] Run /init as init process
[ 3.005819] with arguments:
[ 3.008785] /init
[ 3.011054] with environment:
[ 3.014198] HOME=/
[ 3.016554] TERM=linux
Loading, please wait...
+ panic=30
+ '[' -z ]
+ BOOT=local
+ '[' -n ]
+ '[' none '=' none ]
+ noresume=y
+ mount -t tmpfs -o 'nodev,noexec,nosuid,size=10%,mode=0755' tmpfs /run
+ mkdir -m 0700 /run/initramfs
+ '[' -n /run/initramfs/initramfs.debug ]
+ exec
[ 3.086338] systemd-udevd[199]: Starting version 245.4-4ubuntu3.17
[ 3.097847] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:24 The line takes no effect, ignoring.
[ 3.108341] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:25 The line takes no effect, ignoring.
[ 3.118823] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:29 The line takes no effect, ignoring.
[ 3.129298] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:32 The line takes no effect, ignoring.
[ 3.139740] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:33 The line takes no effect, ignoring.
[ 3.150173] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:34 The line takes no effect, ignoring.
[ 3.160618] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:35 The line takes no effect, ignoring.
[ 3.171099] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:36 The line takes no effect, ignoring.
[ 3.181548] systemd-udevd[200]: /usr/lib/udev/rules.d/50-udev-default.rules:37 The line takes no effect, ignoring.
U-Boot SPL 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800)
WS > Skip chip ID checlDRAM: 1024 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.7(debug):8ef86301-dirty
NOTICE: BL31: Built : 17:07:29, Aug 25 2022
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a082570, model: OrangePi Zero2
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: BL31: WS-master prevent pmix setup
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied
INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
INFO: Changed devicetree.
U-Boot 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero2
I2C: ready
DRAM: 1 GiB
MMC: mmc@4020000: 0
Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Net: phy interface7
Could not get PHY for ethernet@5020000: addr 1
No ethernet found.
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3202 bytes read in 2 ms (1.5 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
131 bytes read in 1 ms (127.9 KiB/s)
22920 bytes read in 5 ms (4.4 MiB/s)
Failed to load '/boot/dtb/allwinner/overlay/-fixup.scr'
11610972 bytes read in 482 ms (23 MiB/s)
21934088 bytes read in 908 ms (23 MiB/s)
Moving Image from 0x40080000 to 0x40200000, end=41740000
## Loading init Ramdisk from Legacy Image at 4ff00000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 11610908 Bytes = 11.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
Loading Ramdisk to 494ed000, end 49fffb1c ... OK
Loading Device Tree to 000000004947f000, end 00000000494ecfff ... OK
Starting kernel ...
U-Boot SPL 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800)
WS > Skip chip ID checlDRAM: 1024 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.7(debug):8ef86301-dirty
NOTICE: BL31: Built : 17:07:29, Aug 25 2022
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a082570, model: OrangePi Zero2
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: BL31: WS-master prevent pmix setup
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied
INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
INFO: Changed devicetree.
U-Boot 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero2
I2C: ready
DRAM: 1 GiB
MMC: mmc@4020000: 0
Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Net: phy interface7
Could not get PHY for ethernet@5020000: addr 1
No ethernet found.
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3202 bytes read in 3 ms (1 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
131 bytes read in 1 ms (127.9 KiB/s)
22920 bytes read in 5 ms (4.4 MiB/s)
Failed to load '/boot/dtb/allwinner/overlay/-fixup.scr'
11610972 bytes read in 482 ms (23 MiB/s)
21934088 bytes read in 908 ms (23 MiB/s)
Moving Image from 0x40080000 to 0x40200000, end=41740000
## Loading init Ramdisk from Legacy Image at 4ff00000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 11610908 Bytes = 11.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
Loading Ramdisk to 494ed000, end 49fffb1c ... OK
Loading Device Tree to 000000004947f000, end 00000000494ecfff ... OK
Starting kernel ...
Loading, please wait...
Starting version 245.4-4ubuntu3.17
U-Boot SPL 2021.10-armbian (Aug 25 2022 - 17:13:08 +0800)
WS > Skip chip ID checlDRAM: 1024 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.7(debug):8ef86301-dirty
NOTICE: BL31: Built : 17:07:29, Aug 25 2022
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a082570, model: OrangePi Zero2
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: BL31: WS-master prevent pmix setup
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied
INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
INFO: Changed devicetree.
检查下主电源5V是不是电流不太够
谢谢！
解决了，的确是