我的bit3搜索不到wifi热点，看启动日志，现实port2（ra0）enter disable state，查看config/wireless，option disable已经设置成0，请问这是为什么？@mangogeek
wifi好了，还是驱动的问题，因为之前没选widora自己的驱动（ranlin sdk mango），在kernel modules里面选了kmod-mt76 和kmod-mac80211，把这两个驱动去掉就恢复正常了。
执行iwinfo命令显示：
root@Widora:/# iwinfo ra0 info
No such wireless device: ra0
root@Widora:/#
我昨晚刷了一遍固件，我想是不是因为驱动冲突了，把kmodel里面的kmod-mt76驱动去掉了，刚刚启动看了一下，确实没看到enter disabled state这条了 但是用手机仍然看不到SSID（应该是没有热点吧），登陆luci看了一下，是这样的（你不知道怎么发图片）：
Wireless Overview
Generic 802.11 Wireless Controller (radio0)
[Signal: 0 dBm / Noise: 0 dBm]
0% SSID: Widora-BA20 | Mode: Master
Wireless is disabled or not associated
[Signal: 0 dBm / Noise: 0 dBm]
0% SSID: UplinkAp | Mode: Client
Wireless is disabled or not associated
log看着没问题啊，执行：
iwinfo ra0 info 看下
BusyBox v1.23.2 (2020-06-02 14:58:37 CST) built-in shell (ash)
_ ___ __
| | / (_)___/ /___ _________ _
| | /| / / / __ / __ \/ ___/ __ `/
| |/ |/ / / /_/ / /_/ / / / /_/ /
|__/|__/_/\__,_/\____/_/ \__,_/
-----------------------------------------------------
CHAOS CALMER (Chaos Calmer, r49378) Ver:0.1.9-20190812 by WIDORA
-----------------------------------------------------
root@Widora:~# cd /
root@Widora:/# wifi
root@Widora:/# vi /etc/init.d/network
root@Widora:/# wifi up
root@Widora:/# cd /etc/config/
root@Widora:/etc/config# ls
dhcp fstab network ubootenv wireless
dropbear luci rpcd ucitrack
firewall mjpg-streamer system uhttpd
root@Widora:/etc/config# vi wireless
root@Widora:/etc/config# wps pressed for 2 seconds
FACTORY RESET
wps pressed for 5 seconds
FACTORY RESET
root@Widora:/etc/config# wps pressed for 0 seconds
root@Widora:/etc/config# wifi
root@Widora:/etc/config#
Widora by mango,V1.0.7
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fb4000
flash manufacture id: ef, device id 40 19
find flash: W25Q256FV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Oct 9 2017 Time:09:06:39
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
RESET MT7628 PHY!!!!!!MT7688 gpio init : wled and wdt by mango
if you press the WPS button will automatically enter the Update mode
0
1
2
3
4
5
6
7
8
9
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
5: Entr ALL LED test mode.
6: Entr Web failsafe mode.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
Image Name: MIPS OpenWrt Linux-3.18.29
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1150518 Bytes = 1.1 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 3.18.29 (wlf@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49378) ) #35 Mon Jun 15 14:12:52 CST 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is WIDORA-BIT5
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00001ea0
[ 0.000000] Readback ErrCtl register=00001ea0
[ 0.000000] Memory: 61296K/65536K available (2544K kernel code, 123K rwdata, 520K rodata, 196K init, 185K bss, 4240K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource_of_init: no matching clocksources found
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered protocol family 16
[ 0.100000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.120000] Switched to clocksource MIPS
[ 0.120000] NET: Registered protocol family 2
[ 0.130000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.140000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.140000] TCP: reno registered
[ 0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.160000] NET: Registered protocol family 1
[ 0.170000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.190000] jffs2: version 2.2 (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.200000] msgmni has been set to 119
[ 0.210000] io scheduler noop registered
[ 0.210000] io scheduler deadline registered (default)
[ 0.220000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[336]
[ 0.220000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[350]
[ 0.230000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.240000] console [ttyS0] disabled
[ 0.240000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[ 0.250000] console [ttyS0] enabled
[ 0.250000] console [ttyS0] enabled
[ 0.260000] bootconsole [early0] disabled
[ 0.260000] bootconsole [early0] disabled
[ 0.270000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[ 0.280000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
[ 0.290000] spi-mt7621 10000b00.spi: sys_freq: 193333333
[ 0.300000] m25p80 spi32766.0: w25q256 (32768 Kbytes)
[ 0.300000] m25p80 spi32766.0: using chunked io
[ 0.310000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.310000] Creating 4 MTD partitions on "spi32766.0":
[ 0.320000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.320000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.330000] 0x000000040000-0x000000050000 : "factory"
[ 0.340000] 0x000000050000-0x000002000000 : "firmware"
[ 0.410000] 2 uimage-fw partitions found on MTD device firmware
[ 0.410000] 0x000000050000-0x000000168e76 : "kernel"
[ 0.420000] 0x000000168e76-0x000002000000 : "rootfs"
[ 0.420000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.430000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.440000] 0x000000f00000-0x000002000000 : "rootfs_data"
[ 0.460000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.460000] mt7621_wdt 10000100.watchdog: Initialized
[ 0.470000] TCP: cubic registered
[ 0.470000] NET: Registered protocol family 17
[ 0.480000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.490000] 8021q: 802.1Q VLAN Support v1.8
[ 0.500000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.510000] Freeing unused kernel memory: 196K (8031f000 - 80350000)
[ 1.760000] init: Console is alive
[ 1.760000] init: - watchdog -
[ 3.930000] usbcore: registered new interface driver usbfs
[ 3.930000] usbcore: registered new interface driver hub
[ 3.940000] usbcore: registered new device driver usb
[ 3.940000] reg_opt_init
[ 3.950000] exFAT: Version 1.2.9
[ 3.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.970000] ehci-platform: EHCI generic platform driver
[ 4.140000] U2PHY P0 set SRCTRL calibration value: 6
[ 4.140000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.150000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.150000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.180000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.180000] hub 1-0:1.0: USB hub found
[ 4.190000] hub 1-0:1.0: 1 port detected
[ 4.190000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.200000] ohci-platform: OHCI generic platform driver
[ 4.210000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 4.210000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.220000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.290000] hub 2-0:1.0: USB hub found
[ 4.290000] hub 2-0:1.0: 1 port detected
[ 4.510000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 4.770000] init: - preinit -
[ 5.300000] rt305x-esw 10110000.esw: link changed 0x00
[ 5.340000] (NULL device *): kill_sig_workq
[ 5.490000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.730000] mount_root: loading kmods from internal overlay
[ 9.090000] jffs2: notice: (343) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.110000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.120000] block: unable to load configuration (fstab: Entry not found)
[ 9.120000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 9.130000] block: unable to load configuration (fstab: Entry not found)
[ 9.140000] block: attempting to load /etc/config/fstab
[ 9.150000] block: unable to load configuration (fstab: Entry not found)
[ 9.150000] block: no usable configuration
[ 9.260000] jffs2: notice: (340) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.510000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.520000] block: unable to load configuration (fstab: Entry not found)
[ 9.530000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 9.530000] block: unable to load configuration (fstab: Entry not found)
[ 9.540000] block: attempting to load /etc/config/fstab
[ 9.540000] block: unable to load configuration (fstab: Entry not found)
[ 9.550000] block: no usable configuration
[ 9.560000] mount_root: overlay filesystem has not been fully initialized yet
[ 9.570000] mount_root: switching to jffs2 overlay
[ 9.590000] procd: - early -
[ 9.600000] procd: - watchdog -
Failed to connect to ubus
[ 10.470000] procd: - ubus -
[ 11.490000] procd: - init -
Please press Enter to activate this console.
[ 12.400000] NET: Registered protocol family 10
[ 12.460000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.470000] i2c /dev entries driver
[ 12.680000] PandoraBox MT76X8 AP Driver Version-4.1.0.0(Aug 8 2019 08:13:30).
[ 12.730000] rt2880-pinmux pinctrl: pin io4 already requested by pinctrl; cannot claim for 10000900.i2c
[ 12.740000] rt2880-pinmux pinctrl: pin-4 (10000900.i2c) status -22
[ 12.740000] rt2880-pinmux pinctrl: could not request pin 4 (io4) from group i2c on device rt2880-pinmux
[ 12.750000] i2c-mt7621 10000900.i2c: Error applying setting, reverse things back
[ 12.760000] i2c-mt7621 10000900.i2c: clock 100 kHz
[ 12.780000] Linux video capture interface: v2.00
[ 12.810000] Enable Ralink GDMA Controller Module
[ 12.820000] GDMA IP Version=3
[ 12.840000] *******Enter codec_wm8960_i2c_probe********
[ 12.850000] soc-audio soc-audio: ASoC: machine MTK APSoC I2S should use snd_soc_register_card()
[ 12.850000] wm8960 0-001a: No platform data supplied
[ 14.860000] ****** wm8960_preinit ******
[ 35.360000] soc-audio soc-audio: wm8960-hifi <-> mt76xx-i2s mapping ok
[ 35.370000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.400000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 35.430000] usbcore: registered new interface driver usbserial
[ 35.430000] usbcore: registered new interface driver usbserial_generic
[ 35.440000] usbserial: USB Serial support registered for generic
[ 35.460000] usbcore: registered new interface driver uvcvideo
[ 35.460000] USB Video Class driver (1.1.1)
[ 35.490000] xt_time: kernel timezone is -0000
[ 35.490000] usbcore: registered new interface driver ch341
[ 35.500000] usbserial: USB Serial support registered for ch341-uart
[ 35.500000] usbcore: registered new interface driver cp210x
[ 35.510000] usbserial: USB Serial support registered for cp210x
[ 35.530000] PPP generic driver version 2.4.2
[ 35.540000] NET: Registered protocol family 24
ETHMODE
3
[ 42.670000] device eth0 entered promiscuous mode
[ 42.670000] br-lan: port 1(eth0) entered forwarding state
[ 42.680000] br-lan: port 1(eth0) entered forwarding state
[ 44.680000] br-lan: port 1(eth0) entered forwarding state
[ 50.860000] br-lan: port 1(eth0) entered disabled state
[ 50.870000] device eth0 left promiscuous mode
[ 50.870000] br-lan: port 1(eth0) entered disabled state
[ 50.910000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 50.970000] device eth0 entered promiscuous mode
[ 51.090000] br-lan: port 1(eth0) entered forwarding state
[ 51.090000] br-lan: port 1(eth0) entered forwarding state
[ 53.090000] br-lan: port 1(eth0) entered forwarding state
[ 54.810000] =====================================================
[ 54.810000] Channel 1 : Busy Time = 38856, Skip Channel = FALSE
[ 54.820000] Channel 2 : Busy Time = 17619, Skip Channel = FALSE
[ 54.820000] Channel 3 : Busy Time = 143, Skip Channel = FALSE
[ 54.830000] Channel 4 : Busy Time = 0, Skip Channel = FALSE
[ 54.830000] Channel 5 : Busy Time = 0, Skip Channel = FALSE
[ 54.840000] Channel 6 : Busy Time = 0, Skip Channel = FALSE
[ 54.850000] Channel 7 : Busy Time = 0, Skip Channel = FALSE
[ 54.850000] Channel 8 : Busy Time = 0, Skip Channel = FALSE
[ 54.860000] Channel 9 : Busy Time = 0, Skip Channel = FALSE
[ 54.860000] Channel 10 : Busy Time = 0, Skip Channel = FALSE
[ 54.870000] Channel 11 : Busy Time = 0, Skip Channel = FALSE
[ 54.870000] Channel 12 : Busy Time = 0, Skip Channel = TRUE
[ 54.880000] Channel 13 : Busy Time = 0, Skip Channel = TRUE
[ 54.890000] =====================================================
[ 54.890000] Rule 3 Channel Busy time value : Min Channel Busy ==> Select Channel 4
[ 54.900000] Min Channel Busy = 0
[ 54.900000] BW = 40
[ 54.930000] |--------------------------------------------------------|
[ 54.940000] |------------Widora wifi driver--version:1.5-------------|
[ 54.950000] |Copyright 2016-2019 by WIDORA TECH. All rights reserved|
[ 54.950000] | This Driver licensing-only runs on Widora HW! |
[ 54.960000] | Found bug? Please contact widora@qq.com , thanks! |
[ 54.970000] |--------------------------------------------------------|
[ 59.930000] =====================================================
[ 59.930000] Channel 1 : Busy Time = 12490, Skip Channel = FALSE
[ 59.940000] Channel 2 : Busy Time = 9717, Skip Channel = FALSE
[ 59.940000] Channel 3 : Busy Time = 68, Skip Channel = FALSE
[ 59.950000] Channel 4 : Busy Time = 6, Skip Channel = FALSE
[ 59.950000] Channel 5 : Busy Time = 21, Skip Channel = FALSE
[ 59.960000] Channel 6 : Busy Time = 77, Skip Channel = FALSE
[ 59.970000] Channel 7 : Busy Time = 38, Skip Channel = FALSE
[ 59.970000] Channel 8 : Busy Time = 18, Skip Channel = FALSE
[ 59.980000] Channel 9 : Busy Time = 0, Skip Channel = FALSE
[ 59.980000] Channel 10 : Busy Time = 0, Skip Channel = FALSE
[ 59.990000] Channel 11 : Busy Time = 0, Skip Channel = FALSE
[ 59.990000] Channel 12 : Busy Time = 0, Skip Channel = TRUE
[ 60.000000] Channel 13 : Busy Time = 1, Skip Channel = TRUE
[ 60.010000] =====================================================
[ 60.010000] Rule 3 Channel Busy time value : Min Channel Busy ==> Select Channel 9
[ 60.020000] Min Channel Busy = 0
[ 60.020000] BW = 40
[ 60.060000] |--------------------------------------------------------|
[ 60.060000] |------------Widora wifi driver--version:1.5-------------|
[ 60.070000] |Copyright 2016-2019 by WIDORA TECH. All rights reserved|
[ 60.080000] | This Driver licensing-only runs on Widora HW! |
[ 60.080000] | Found bug? Please contact widora@qq.com , thanks! |
[ 60.090000] |--------------------------------------------------------|
[ 64.450000] =====================================================
[ 64.450000] Channel 1 : Busy Time = 19900, Skip Channel = FALSE
[ 64.460000] Channel 2 : Busy Time = 17987, Skip Channel = FALSE
[ 64.460000] Channel 3 : Busy Time = 8, Skip Channel = FALSE
[ 64.470000] Channel 4 : Busy Time = 0, Skip Channel = FALSE
[ 64.470000] Channel 5 : Busy Time = 18, Skip Channel = FALSE
[ 64.480000] Channel 6 : Busy Time = 69, Skip Channel = FALSE
[ 64.490000] Channel 7 : Busy Time = 17, Skip Channel = FALSE
[ 64.490000] Channel 8 : Busy Time = 38, Skip Channel = FALSE
[ 64.500000] Channel 9 : Busy Time = 0, Skip Channel = FALSE
[ 64.500000] Channel 10 : Busy Time = 0, Skip Channel = FALSE
[ 64.510000] Channel 11 : Busy Time = 0, Skip Channel = FALSE
[ 64.510000] Channel 12 : Busy Time = 0, Skip Channel = TRUE
[ 64.520000] Channel 13 : Busy Time = 4, Skip Channel = TRUE
[ 64.530000] =====================================================
[ 64.530000] Rule 3 Channel Busy time value : Min Channel Busy ==> Select Channel 4
[ 64.540000] Min Channel Busy = 0
[ 64.540000] BW = 40
[ 64.580000] |--------------------------------------------------------|
[ 64.580000] |------------Widora wifi driver--version:1.5-------------|
[ 64.590000] |Copyright 2016-2019 by WIDORA TECH. All rights reserved|
[ 64.600000] | This Driver licensing-only runs on Widora HW! |
[ 64.600000] | Found bug? Please contact widora@qq.com , thanks! |
[ 64.610000] |--------------------------------------------------------|
[ 68.860000] random: nonblocking pool is initialized
[ 68.910000] =====================================================
[ 68.910000] Channel 1 : Busy Time = 9844, Skip Channel = FALSE
[ 68.920000] Channel 2 : Busy Time = 6357, Skip Channel = FALSE
[ 68.920000] Channel 3 : Busy Time = 0, Skip Channel = FALSE
[ 68.930000] Channel 4 : Busy Time = 0, Skip Channel = FALSE
[ 68.930000] Channel 5 : Busy Time = 0, Skip Channel = FALSE
[ 68.940000] Channel 6 : Busy Time = 12, Skip Channel = FALSE
[ 68.950000] Channel 7 : Busy Time = 0, Skip Channel = FALSE
[ 68.950000] Channel 8 : Busy Time = 0, Skip Channel = FALSE
[ 68.960000] Channel 9 : Busy Time = 0, Skip Channel = FALSE
[ 68.960000] Channel 10 : Busy Time = 0, Skip Channel = FALSE
[ 68.970000] Channel 11 : Busy Time = 0, Skip Channel = FALSE
[ 68.970000] Channel 12 : Busy Time = 0, Skip Channel = TRUE
[ 68.980000] Channel 13 : Busy Time = 7, Skip Channel = TRUE
[ 68.990000] =====================================================
[ 68.990000] Rule 3 Channel Busy time value : Min Channel Busy ==> Select Channel 3
[ 69.000000] Min Channel Busy = 0
[ 69.000000] BW = 40
[ 69.040000] |--------------------------------------------------------|
[ 69.040000] |------------Widora wifi driver--version:1.5-------------|
[ 69.050000] |Copyright 2016-2019 by WIDORA TECH. All rights reserved|
[ 69.060000] | This Driver licensing-only runs on Widora HW! |
[ 69.060000] | Found bug? Please contact widora@qq.com , thanks! |
[ 69.070000] |--------------------------------------------------------|
发完整日志